Juniper-networks SRX 210 Bedienungsanleitung Seite 103
- Seite / 176
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
NOTE: Downloading of purchased licenses from the setup wizard is
available only in Junos OS Release 11.2R3 or later.
•
Configuration of a chassis cluster—Perform the initial configuration of the chassis
cluster using a console connection. Before you perform the initial configuration, connect
the built-in Ethernet ports as follows:
•
Port 0/6—Connect to the out-of-band management network for management of
the device. When you enable chassis clustering as part of configuring the chassis
cluster, the management interface (fxp0) is automatically created on this port.
•
Port 0/7—Connect to the other device in the chassis cluster. When you enable chassis
clustering, the control interface between the two devices (fxp1) is automatically
created on this port.
You must also make another connection between the two devices for the fabric link.
You can use any Fast Ethernet or Gigabit Ethernet port for this connection. You must
configure the interface you choose as the fabric link. For more information on configuring
chassis clusters, see the Security Basics.
Mapping the Chassis Cluster Ports
On the SRX210 Services Gateway, the fxp1 port is not user-configurable when the services
gateway is operating in chassis cluster mode.
The fxp0 port is dedicated as the out-of-band management interface for each of the
devices in the chassis cluster setup and the fxp1 port is dedicated as the chassis-cluster
control port.
Table 33 on page 87 shows the mapping of the chassis cluster ports.
Table 33: Mapping the Chassis Cluster Ports on an SRX210 Services
Gateway
Management InterfaceEthernet Ports on SRX210 Services Gateway
fxp0 (management port)0/6 (fe-0/0/6)
fxp1 (control port)0/7 (fe-0/0/7)
Junos OS automatically creates the fxp0 and fxp1 interfaces on these ports when the
SRX210 Services Gateway is operating in chassis cluster mode.
For more information, see the following topics:
•
Interfaces for Security Devices
•
Security Basics
87Copyright © 2013, Juniper Networks, Inc.
Chapter 15: Performing Initial Software Configuration on the SRX210 Services Gateway
- SRX210 Services Gateway 1
- END USER LICENSE AGREEMENT 2
- Table of Contents 5
- Part 4 Appendixes 8
- Part 5 Index 9
- About This Guide 11
- Table 1: Notice Icons 12
- Obtaining Documentation 13
- Documentation Feedback 14
- Requesting Technical Support 14
- CHAPTER 1 19
- Components and Specifications 23
- ValueSpecification 24
- Memory, and PoE Versions) 25
- ComponentNumber 26
- Interfaces (continued) 28
- SRX210 Services Gateway LEDs 29
- Front Panel LEDs 30
- LEDs (continued) 31
- Ethernet Port LEDs 31
- Table 10 on page 16 32
- Boot Devices 33
- Dual-Root Partitioning Scheme 33
- Air flow 35
- CAUTION: 37
- ATTENTION: 37
- CHAPTER 3 39
- Introduction 39
- Supported Modem Types 39
- Services Gateway 40
- Using the 3G ExpressCard 40
- Key Features 40
- Physical Specifications 41
- CommandAction 43
- CDMA ExpressCards 43
- Commands (continued) 44
- Ethernet Support 45
- PoE Classes and Power Ratings 46
- Gateway (continued) 47
- Interface Modules 49
- Gateway Installation 53
- Installation (continued) 54
- Requirements 56
- Requirement for Clearance 58
- Recommended 58
- ClearanceLocation 58
- Documentation 59
- CHAPTER 8 63
- CHAPTER 9 65
- QuantityComponent 66
- QuantityPart 67
- Installation 69
- Rack-Mount Installation 70
- Desk-Mount Installation 71
- Wall-Mount Installation 72
- CHAPTER 11 73
- 60-Watt Power Supply 74
- 150-Watt Power Supply 75
- Mounting Brackets 76
- Services Gateway in a Rack 77
- Power Supply Adapter Tray 77
- Vertical Stand 79
- Services Gateway on a Desk 79
- Services Gateway on a Wall 81
- CHAPTER 12 83
- Autoinstallation 91
- CHAPTER 14 93
- 192.168.1.1 and use DHCP to 94
- ValuePort Settings 96
- Gateway End 97
- CHAPTER 15 101
- J-Web Interface 107
- Start to 109
- Your ActionFunctionField 110
- Services Gateway Hardware 113
- Hardware Components 115
- Components (continued) 116
- CHAPTER 17 117
- Possible Causes and 119
- Corrective Actions 122
- Possible Cause and Corrective 124
- ActionMeaningLED Status 124
- Appendixes 127
- Information 129
- Qualified Personnel Warning 132
- ADSL 2/2+ A 135
- Class 1 Laser Product Warning 141
- Class 1 LED Product Warning 141
- Laser Beam Warning 142
- Warnings 143
- Jewelry Removal Warning 144
- Lightning Activity Warning 146
- Operating Temperature Warning 146
- Product Disposal Warning 147
- Korean Class B Warning 151
- SRX210 Services Gateway Power 155
- Guidelines, Requirements, and 155
- Specifications 155
- GuidelineSite Wiring Factor 156
- 1.5 A maximum 157
- AC system current rating 157
- Grounding lug 158
- APPENDIX C 159
- Port (10/100 Mbps) 160
- Port (1 Gbps) 160
- Port (1 Gbps) (continued) 161
- Hardware 163
- Power Supply 0 165
- Contacting Customer Support 166
- Packing the Services Gateway 167
- Index on page 155 169
Verwandte Produkte und Handbücher für Hardware Juniper-networks SRX 210
Hardware Juniper-networks M5 Bedienungsanleitung
(205 Seiten)
(205 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.411 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern