Juniper-networks ERX-1410 Bedienungsanleitung Seite 56
- Seite / 184
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
CHAPTER 3
Installing ERX Modules
3-10
Figure 3-8 Installing an SRP module
9 Insert the module into the backplane by simultaneously depressing
both ejectors (as shown in Figure 3-7) and exerting forward pressure
on the module.
10 Tighten the module’s captive screws using a Phillips screwdriver.
Turn both screws several times before tightening them completely to
allow the module to sit correctly.
Installing Line Modules and Their I/O Modules
This section describes the procedures for installing line and I/O modules.
Note: Install the I/O module before you install the corresponding line module;
otherwise, the ERX system diagnostics fail, and after the line module has tried to
reboot, its status will be “inactive” when you issue a show version command.
ERX-1400
Ejector in open position
- ERX Edge Routers 1
- Installation and User Guide 1
- EC Declaration of Conformity 4
- SOFTWARE LICENSE AGREEMENT 5
- Contents 10
- About This Guide 15
- Audience 16
- Conventions 16
- Documentation 17
- Abbreviations 18
- Contacting Customer Support 19
- ERX System Overview 21
- ERX-1400 Series 22
- The ERX System 23
- OC3 I/O module 25
- CT3/T3 I/O modules 25
- SRP I/O modulePower switches 25
- Power input module 25
- Where the ERX System Fits In 26
- ERX System Modules 27
- SRP Module 28
- Nonvolatile Storage 28
- SRP I/O Module 29
- Line Modules 30
- Packet Classification 30
- Network Management Tools 31
- Redundancy Features 31
- NVS Cards 32
- CHAPTER 1 34
- The Next Step 35
- Installing the ERX 37
- CHAPTER 2 38
- Installing the ERX System 38
- Unpacking the ERX-1400 Series 39
- Unpacking the ERX-700 Series 40
- ERX-1400 41
- Rack-Mounted Installation 42
- Installation 43
- ERX-1400 system 45
- ERX-700 system 45
- Installing ERX Modules 47
- ERX-700 seriesERX-1400 series 48
- Overview 49
- Protecting Modules and Slots 50
- Order of Installation 51
- Installing an SRP Module 54
- Ejector in open position 56
- Line Module I/O Module 58
- Removing a Module 59
- faceplate 60
- Installing the Line Modules 61
- Installing the I/O Modules 62
- CHAPTER 3 64
- Cabling the ERX 65
- Cabling Your ERX System 66
- Cabling the SRP I/O Module 71
- 26-AWG wire 72
- Wire-wrap connectors 72
- (North America, Japan) 72
- BNC (Europe) 72
- Console Ports 73
- Cabling I/O Modules 74
- Cabling RJ-45 Connectors 75
- Cabling RJ-48C Connectors 76
- Cabling LC Duplex Connectors 77
- Cabling SC Duplex Connectors 78
- Cabling SMB Connectors 79
- Cabling X.21/V.35 Connectors 80
- CHAPTER 4 82
- Cabling the ERX System 82
- Accessing the ERX 83
- Console Port Setup 84
- Assigning an IP Address 85
- Telnet Setup 86
- Powering Up the 89
- Powering Up 90
- Powering Down 91
- Maintaining the ERX 93
- 1 Enter the halt command 94
- Replacing an NVS Card 96
- Faceplate 97
- Release button 97
- NVS card 97
- Removing SFPs 98
- Installing SFPs 99
- Verifying the Installation 100
- Cleaning the System 101
- Replacing Fan Trays 101
- ERX-1400 series 102
- Removing the Fan Tray 103
- Installing the Fan Tray 103
- ERX-700 Series 104
- CHAPTER 7 106
- Maintaining the ERX System 106
- Troubleshooting 107
- LED Activity 108
- Module Cables 108
- Initialization Sequence 108
- Understanding Status LEDs 109
- • SRP module (Figure 8-1) 111
- Status LEDs 112
- Status LEDs 112
- LED Activity During Booting 113
- Abnormal LED Activity 114
- Redundancy Status 115
- Detecting Double-Bit Errors 117
- Fixing Double-Bit Errors 118
- System Specifications 119
- APPENDIX A 122
- Module Specifications 123
- Performance Specifications 126
- Connection Information 129
- › 0–68.5 m (0–225 feet) 132
- › 69–137 m (226–450 feet) 132
- › min: –9.5 dBm 133
- › max: –4 dBm 133
- › min: –17 dBm 133
- › max: –3 dBm 133
- APPENDIX B 144
- Cable Pinouts 145
- CT1 and CE1 I/O Modules 148
- 3456789 111213141516171819 150
- Preparing Your Site 153
- Environmental Requirements 154
- Safety Guidelines 154
- Rack Requirements 155
- Space Requirements 156
- APPENDIX D 158
- Cabling Recommendations 159
- Installing ERX System 161
- Software 161
- APPENDIX E 162
- Task 11: Reboot the System 166
- 5 Run the reload command 167
- Task 8: Reboot the System 171
- Task 2: Access the Boot Mode 172
- Task 3: Assign an IP Address 173
- Task 7: Reboot the System 174
- Declaration of 177
- Conformity 177
Verwandte Produkte und Handbücher für Hardware Juniper-networks ERX-1410
Hardware Juniper-networks J4350 Bedienungsanleitung
(284 Seiten)
(284 Seiten)
Hardware Juniper-networks M7I Bedienungsanleitung
(105 Seiten)
(105 Seiten)
Hardware Juniper-networks M5 Bedienungsanleitung
(205 Seiten)
(205 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern